Brodit
Brodit 532306 Active holder for fix. instal. 532306
(No reviews yet)
Write a Review
- UPC:
- 0000000000000
- MPN:
- 532306
- Condition:
- New
- Availability:
- Available to Order: 3 - 4 weeks leadtime
Description
Active holder for fixed installation
With tilt swivel. Slim design with charger integrated in the holder.
The cables are to be connected inside the dashboard, this gives a discreet, neat installation without cables hanging over the interior. The charging device is integrated in the holder itself, so there is no large charging box on the cable.
12/24 Volt. The product is E-approved. Connect the power cable with a 2 A fuse. 2 A charger. Professional installation recommended.
The holder is attached onto a tilt swivel and can be adjusted in order to avoid light reflection. The holder fits devices both with standard and extended battery. Attach onto ProClip Mounting Platform.
INSTALLATION INSTRUCTIONS:
Please read all of the instructions and look at the pictures before attaching the holder. Important Note: Route the cable from the holder into the vehicle dashboard and route the power cable from the charger unit to the power supply source in the vehicle and connect as follows: 1. Connect the White wire to a Negative Ground connection of the vehicle or the vehicle chassis. 2. Connect the Red wire to a 12/24 Volt power supply in the vehicle that is controlled by the ignition switch of the vehicle.
1. Loosen the screw in the center of the holder so you can remove the tilt swivel attaching plate on the back.
2. Place the attaching plate onto the desired position. Screw the attaching plate into place with the enclosed screws. Place the holder over the attaching plate so the screw fits in the hole in the tilt swivel. Tighten the screw until the holder is firmly in place, but still can be adjusted.
3. To place the device in the holder: Place the botto part of the device into the holder. Slide the device downward into place in the holder. To remove the device fron the holder: Open the latch on the holder. Then the device is set frre, lift it upward out of the holder.
4. The holder is in place.
Design
Compatibility
Datalogic Falcon
Material
Plastic
Mobile device type
Handheld mobile computer
Product colour
Black
Proper use
Car
Type
Active holder
Multimedia
Built-in speaker(s)
No
Package dimensions
Gross Weight (Package, kg)
0.45 kg
Power
Built-in charger
Yes
Power source type
Cigar lighter
Product dimensions
Net Weight (Product, kg)
0.35 kg
Vendor information
Brand Name
Brodit
Homepage
http://www.brodit.se/product.html?locale=se&id=532306
Warranty
1 Year(s)
View AllClose
With tilt swivel. Slim design with charger integrated in the holder.
The cables are to be connected inside the dashboard, this gives a discreet, neat installation without cables hanging over the interior. The charging device is integrated in the holder itself, so there is no large charging box on the cable.
12/24 Volt. The product is E-approved. Connect the power cable with a 2 A fuse. 2 A charger. Professional installation recommended.
The holder is attached onto a tilt swivel and can be adjusted in order to avoid light reflection. The holder fits devices both with standard and extended battery. Attach onto ProClip Mounting Platform.
INSTALLATION INSTRUCTIONS:
Please read all of the instructions and look at the pictures before attaching the holder. Important Note: Route the cable from the holder into the vehicle dashboard and route the power cable from the charger unit to the power supply source in the vehicle and connect as follows: 1. Connect the White wire to a Negative Ground connection of the vehicle or the vehicle chassis. 2. Connect the Red wire to a 12/24 Volt power supply in the vehicle that is controlled by the ignition switch of the vehicle.
1. Loosen the screw in the center of the holder so you can remove the tilt swivel attaching plate on the back.
2. Place the attaching plate onto the desired position. Screw the attaching plate into place with the enclosed screws. Place the holder over the attaching plate so the screw fits in the hole in the tilt swivel. Tighten the screw until the holder is firmly in place, but still can be adjusted.
3. To place the device in the holder: Place the botto part of the device into the holder. Slide the device downward into place in the holder. To remove the device fron the holder: Open the latch on the holder. Then the device is set frre, lift it upward out of the holder.
4. The holder is in place.
Design
Compatibility
Datalogic Falcon
Material
Plastic
Mobile device type
Handheld mobile computer
Product colour
Black
Proper use
Car
Type
Active holder
Multimedia
Built-in speaker(s)
No
Package dimensions
Gross Weight (Package, kg)
0.45 kg
Power
Built-in charger
Yes
Power source type
Cigar lighter
Product dimensions
Net Weight (Product, kg)
0.35 kg
Vendor information
Brand Name
Brodit
Homepage
http://www.brodit.se/product.html?locale=se&id=532306
Warranty
1 Year(s)